Specifications, Properties, Classifications and Classes

The largest end use for copper is in the building industry. Within the building industry the use of copper based materials is broad. Construction industry related applications for copper include:

• Roofing
• Cladding
• Rainwater systems
• Heating systems
• Water pipes and fittings
• Oil and gas lines
• Electrical wiring

The building industry is the largest single consumer of copper alloy. The following list is a breakdown of copper consumption by industry on an annual basis:

• Building industry – 47%
• Electronic products – 23%
• Transportation – 10%
• Consumer products – 11%
• Industrial machinery – 9%

Copper and copper alloy can be used in an extraordinary range of applications. Some of these applications include:

• Power transmission lines
• Architectural applications
• Cooking utensils
• Spark plugs
• Electrical wiring, cables and busbars
• High conductivity wires
• Electrodes
• Heat exchangers
• Refrigeration tubing
• Plumbing
• Water-cooled copper crucibles

Copper has a face centred cubic crystal structure. It is yellowish red in physical appearance and when polished develops a bright metallic lustre.

Copper is a tough, ductile and malleable material. These properties make copper extremely suitable for tube forming, wire drawing, spinning and deep drawing. The other key properties exhibited by copper and its alloys include:

• Excellent heat conductivity
• Excellent electrical conductivity
• Good corrosion resistance
• Good biofouling resistance
• Good machinability
• Retention of mechanical and electrical properties at cryogenic temperatures
• Non-magnetic

The melting point for pure Copper is 1083ºC.

The electrical conductivity of Copper is second only to silver. The conductivity of Copper is 97% that of silver. Due to its much lower cost and greater abundance, Copper has traditionally been the standard material used for electricity transmission applications.

However, weight considerations mean that a large proportion of overhead high voltage power lines now use aluminium rather than copper by weight, the conductivity of aluminium is around twice that of copper. The aluminium alloys used do have a low strength and need to be reinforced with a galvanised or aluminium coated high tensile steel wire in each strand.

Although additions of other elements will improve properties like strength, there will be some loss in electrical conductivity. As an example a 1% addition of cadmium can increase strength by 50%. However, this will result in a corresponding decrease in electrical conductivity of 15%.

All copper alloys resist corrosion by fresh water and steam. In most rural, marine and industrial atmospheres copper alloys also resistant to corrosion. Copper is resistant to saline solutions, soils, non-oxidising minerals, organic acids and caustic solutions. Moist ammonia, halogens, sulphides, solutions containing ammonia ions and oxidising acids, like nitric acid, will attack Copper. Copper alloys also have poor resistance to inorganic acids.

The corrosion resistance of copper alloys comes from the formation of adherent films on the material surface. These films are relatively impervious to corrosion therefore protecting the base metal from further attack.

Copper Nickel alloys, aluminium Brass, and aluminium demonstrate superior resistance to saltwater corrosion.

Most copper alloys will develop a blue-green patina when exposed to the elements outdoors. Typical of this is the colour of the copper Statue of Liberty in New York. Some copper alloys will darken after prolonged exposure to the elements and take on a brown to black colour.

Lacquer coatings can be used to protect the surface and retain the original alloy colour. An acrylic coating with benzotriazole as an additive will last several years under most outdoor, abrasion-free conditions.

Commonly employed processes such as brazing, welding and soldering can be used to join most copper alloys. Soldering is often used for electrical connections. High Lead content alloys are unsuitable for welding.

Copper and copper alloys can also be joined using mechanical means such as rivets and screws.

Although able to be work hardened, Copper and copper alloys can be both hot and cold worked.

Ductility can be restored by annealing. This can be done either by a specific annealing process or by incidental annealing through welding or brazing procedures.

Copper alloys can be specified according to temper levels. The temper is imparted by cold working and subsequent degrees of annealing.

Typical tempers for copper alloys are

• Soft
• Half-hard
• Hard, spring
• Extra-spring

Yield strength of a hard-temper copper alloys is approximately two-thirds of the materials’ tensile strength.

Designation systems for Copper are not specifications, but methods for identifying chemical compositions. Property requirements are covered in ASTM, government and military standards for each composition.

The method for designating copper alloys is an expansion upon the system developed by the U.S. copper and brass industry. Their old system used 3 digits, the new Unified Numbering System for Metals and Alloys (UNS) system uses five digits preceded by the letter C.

As an example the forging brass known as copper alloys 377 is known as C37700 under the UNS system. Wrought compositions are included in the designations from C10000 through to C79900. Casting alloys are assigned numbers from C80000 through to C99900

The UNS designations are summarised in the following table:

Wrought copper alloys are produced using a variety of different production methods. These methods including processes such as annealing, cold working, hardening by heat treatments or stress relieving.

Within the wrought and cast categories for copper alloys, the compositions can be divided into the following main families:

• Pure Coppers
• High Copper Alloys
• Brasses
• Bronzes

The Pure Coppers have a Copper content of 99.3% or higher.

Wrought high copper alloys have Copper contents of less than 99.3% but more than 96% but don’t fall into another copper alloys group. Cast high copper alloys have Copper contents in excess of 94%. Silver may be added to impart special properties.

Brasses contain Zinc as the principal alloying element.

Other alloying elements may also be present to impart advantageous properties. These elements include Iron, aluminium, Nickel and Silicon.

Brasses are most commonly characterised by their free machining grades by which machining standards are set for all other metals.

Brasses can also have high corrosion resistance and high tensile strength. Some Brasses are also suited to hot forging.

Adding Lead to a brass composition can result in a brass with the ability to be rapidly machined. It will also produce less tool wear. Adding aluminium, Iron and Manganese to brass improves strength. Silicon additions improve wear resistance.

Brasses are divided into two classes and three families.

Brasses are divided into two classes. These are:

• The alpha alloys, with less than 37% Zinc. These alloys are ductile and can be cold worked.
• The alpha/beta or duplex alloys with 37-45% Zinc. These alloys have limited cold ductility and are typically harder and stronger.

There are three main families of wrought alloy brasses:

• Copper-Zinc alloys
• Copper-Zinc-Lead alloys (Leaded brasses)
• Copper-Zinc-Tin alloys (Tin brasses)

Cast brass alloys can be broken into four main families:

• Copper-Tin-Zinc alloys (red, semi-red and yellow brasses)
• Manganese Bronze alloys (high strength yellow brasses) and Leaded Manganese Bronze alloys (leaded high strength yellow brasses)
• Copper-Zinc-Silicon alloys (Silicon brasses and bronzes)
• Cast Copper-Bismuth and Copper-Bismuth-Selenium alloys.

The term bronze originally described alloys with Tin as the only or principal alloying element.

Modern day bronze tend to be copper alloys in which the major alloying element is not Nickel or Zinc.

Bronzes can be further broken down into four families for both wrought and cast alloys.

The wrought bronze alloy families are:

• Copper-Tin-Phosphorus alloys (Phosphor Bronzes)
• Copper-Tin-Lead-Phosphorus alloys (Leaded Phosphor Bronzes)
• Copper-Aluminium alloys (Aluminium Bronzes)
• Copper-Silicon alloys (Silicon Bronzes)

The cast bronze alloy families are:

• Copper-Tin alloys (Tin Bronzes)
• Copper-Tin-Lead alloys (Leaded and high leaded Tin Bronzes)
• Copper-Tin-Nickel alloys (nickel-tin bronzes)
• Copper-Aluminium alloys (Aluminium Bronzes)

As the name suggests, the principal alloying element is Nickel. They can contain other alloying elements or simply have Nickel alone.

These alloys are commonly known as “Nickel Silvers” due to the colour of the alloy. They contain Zinc and Nickel as the principal alloying elements and may also contain other alloying elements.

When alloys have chemical compositions that do not fall into any of the other categories mentioned, they are grouped together as “special alloys”.

Free machining properties are imparted upon copper alloys by the addition of Sulphur and Tellurium.

Copper alloys are highly suited to recycling. Around 40% of the annual consumption of Copper alloys is derived from recycled Copper materials.

DISCLAIMER

This Data is indicative only and must not be seen as a substitute for the full specification from which it is drawn. In particular, the mechanical property requirements vary widely with temper, product and product dimensions. The information is based on our present knowledge and is given in good faith. However, no liability will be accepted by the Company is respect of any action taken by any third party in reliance thereon.

As the products detailed may be used for a wide variety of purposes and as the Company has no control over their use; the Company specifically excludes all conditions or warranties expressed or implied by statute or otherwise as to dimensions, properties and/or fitness for any particular purpose.

Any advice given by the Company to any third party is given for that party’s assistance only and without liability on the part of the Company. Any contract between the Company and a customer will be subject to the company’s Conditions of Sale. The extent of the Company’s liabilities to any customer is clearly set out in those Conditions; a copy of which is available on request.

This information has been sourced, reviewed and adapted from materials provided by Aalco – Ferrous and Non-Ferrous Metals Stockist.